Pellet Fan
Pit Talk -- Comments and Questions Regarding These Pellet Pits => recteq => Topic started by: GatorDave on May 01, 2018, 11:00:46 AM
-
Well I finally pulled the trigger on a new grill. I bought the Bullseye to replace my gas burner and most likely my Weber gas lighting charcoal grill. Of course I still haven't figured out which smoker to buy, but that is a decision for another day.
-
Cool. Let us know your thoughts after a few cooks. I just sold my gasser and am considering the Bullseye or possibly a Weber Performer.
-
I love my bulleye for fast grilling . Very convenient
Sent from my Pixel 2 XL using Tapatalk
-
Cool. Let us know your thoughts after a few cooks. I just sold my gasser and am considering the Bullseye or possibly a Weber Performer.
My Weber is essentially a performer with gas ignition. I've had it for over 20 years and still love it. It was definitely $400 well spent. I'm thinking I'm going to like the pellet cooking better though. We shall see. I'm hopeful on this. It seems like the Bullseye will be even less fuss than my Weber. :)
-
Well, I have the first weekend under my belt, and am extremely happy with my decision. I bought this to replace my gas and charcoal grills, and it does an amazing job replacing them. I also decided to try a low and slow cook with it, and was pleasantly surprised. I can't wait till I can figure out which smoker I'm going to buy. As great as my cooking weekend was, I did have a couple issues with the grill. I was having an issue with heat blowing out directly on the handle due to a late part added by rec tec. I'm building a guard to put in place today which should solve that issue. It was causing the handle to get hot hot hot. If I can't get the stickiness out of the handle caused by the heat, I'm going to have to get a new handle. Ocd issues..lol. The other issue I had was getting all of the holes to line up on the legs. I finally gave up on putting the last two screws in because they just would not align. I'll probably go back and drill out new holes at some point in the future, but I wanted to cook Friday.
-
I am curious as to what the " late part " is and what it does other than directing heat to the handle?
-
I believe it was a washer. From what I’ve read the lid was too tight causing smoke to back into the hopper.
-
I am curious as to what the " late part " is and what it does other than directing heat to the handle?
I think they were having an air flow issue and the fire going back towards the hopper. They sent a little part, (in a separate bag with instructions, that gaps the lid just a touch) and the place to mount it is on the front which means that gap allows the heat to blow out directly on the handle. I have made them aware of this, so they are looking into it. The handle didn't seem to get hot enough to burn, but it was definitely hot enough to be very uncomfortable.
-
I haven’t had a problem with the handle getting hot. I have however still had back pressure smoke even with the new part. I also worry about a auger/hopper fire in the bullseye in a way I never have with others. The design of it causes the pellets at the end of the auger to get glowing every time.
-
I haven’t had a problem with the handle getting hot. I have however still had back pressure smoke even with the new part. I also worry about a auger/hopper fire in the bullseye in a way I never have with others. The design of it causes the pellets at the end of the auger to get glowing every time.
One thing I learned very quickly was not to go from full hot to off on the auger feed. When I did this on my first cook, it gradually burned pellets back into the auger tube. Now I turn the feed down to the slowest setting and let it burn down a bit before turning off the auger feed completely. That fixed that issue.
-
Well, I built a guard for the handle which has helped immensely. Now I just have to be careful not to hit the guard with my hand since it does get hot enough to burn.
-
I have however still had back pressure smoke even with the new part. I also worry about a auger/hopper fire in the bullseye in a way I never have with others. The design of it causes the pellets at the end of the auger to get glowing every time.
I've only operated mine twice, both times in the 200° range. I didn't install the lid-propping part because my lid fits loosely. Quite a lot of smoke pours out around the edges. So I don't have a need to vent it or first open the lid slightly before opening completely.
This is the first unit I've owned where the auger tube ends at the fire box. As a result, I've been examining the pellets that sit at the drop zone while the fire burns down. They appear to be slightly charred but probably not ignited. The hopper has a clamp to hold the lid down tight that may prevent air from blowing up the auger tube and carrying fire to the hopper.
It sits on a wooden deck. I intend to monitor it, especially during higher-temperature cooks. If necessary, users can vacuum the hopper empty and run the auger tube empty after each cook.
-
My Bullseye is for sale. Lit four times. Half price. PM me for details.
My is on Craigslist right now as well. Glad I'm not the only one.
-
Just some info on this. I got the temp up to 700 degrees on my cook today. Ribeyes yum.
-
So do you like it overall? Good option for hot and fast grilling?
-
I definitely have no complaints with the cooking. It works like I hoped it would. I wish the build quality was better. At some point I’m going to beef it up.
-
I used a lumberjack 100% hickory blend in it which is why I got those higher temps. I was cooking a couple of 3" thick ribeyes. I seared them first then went low and slow to finish them off. I was having trouble getting the temps below 270. I had to prop the lid open a bit to get the pit down to 250 on the lowest pellet feed setting.
-
I threw a 3" thick ribeye on the Bullseye this weekend. It was pretty xxxx tasty. The searing was easy. The low and slow was a bit tougher due to having to constantly monitor the temp.